![artcam pro mach 3 artcam pro mach 3](https://wooddesigner.org/wp-content/uploads/2017/12/optinest_nesting_map_dxf_output.jpg)
- ARTCAM PRO MACH 3 SERIAL
- ARTCAM PRO MACH 3 UPDATE
- ARTCAM PRO MACH 3 WINDOWS 10
- ARTCAM PRO MACH 3 ANDROID
- ARTCAM PRO MACH 3 SOFTWARE
More importantly I was doing three minutes subs without guiding and saw nice round stars. After two iterations of PA ,I checked it against SharpCap and RAPAS and it was dead- on with both. The Raspberry Pi software/plate solve in the AAP does a wonderful job of polar alignment.
ARTCAM PRO MACH 3 UPDATE
Just an update on the ASI AIR Pro and the Mach 1( CP4). The first Mach 1 question I have for the group is: Do folks use the hand controller to set up park and reset the R/A and Dec THEN sync to the ASIAIR Pro? How exactly do integrate Sky Safari with the Mach 1 and ASI AIR RPO date loop? Thanks again for the positive suggestions. Oh, I shoot with Stellarvue 115mm f/7 scope. These CMOS cameras are really nice, except I ended up adding 2 inches to my focuser tube to come to focus, I guess I could also use a diagonal perhaps less flexion, suggestions welcome. Dec took one minute to get to 02", but when I tightened the RA lever there was significant shift. I used the ASI AIR Pro app to plate solve the Polar Alignment on the Mach 1. Now I can also use my iPad and my Win 10 Blue Stack emulation at the same and the speed is pretty decent. First the good news, I used a FIDI USB cable and it connected the USB port to the ASI Air Pro first time. Hi all, Real progress and some more questions using the ASI AIR PRO. On Wed, at 7:29 AM Lee Decovnick wrote: Hi all, But with moderate focal lengths (AP130 f/6 and shorter), the ASIAIR guiding has been good enough. My only real remaining frustration with this setup is with the guiding - the simplified version of PhD on the ASIAIR does not have many means of fine-tuning your guiding, and I am pretty sure I did better using the real PhD2 with a laptop.
ARTCAM PRO MACH 3 ANDROID
I then have the ASIAIR communicating wirelessly to my Samsung 10-inch Android tablet. That has been a reliable connection method for me. For me, since my mount does not have integral wi-fi, I simply do a wired connection from the mount's RS232 port into one of the ASIAIR's USB's ports.
![artcam pro mach 3 artcam pro mach 3](https://i.ytimg.com/vi/STwABpeOeGY/maxresdefault.jpg)
I am successful getting it to talk to the mount, control slews to targets, do the plate solving, etc. Some of us are slow to catch on to new technology, but the ASIAIR Pro is getting me there.
ARTCAM PRO MACH 3 SOFTWARE
On Thu, at 02:03, Kevin Cook wrote: Hi Lee - I was always "old school" with my Mach 1 (CP3), using the RAPAS to polar align, the hand controller to find targets, and then a variety of software programs to manage the image capture. On Wed, at 22:29, Lee Decovnick wrote: Hi all, Hi Lee - I was always "old school" with my Mach 1 (CP3), using the RAPAS to polar align, the hand controller to find targets, and then a variety of software programs to manage the image capture. I do not have APCC loaded on my Window machine, do I need to do so?Īm I aiming for a bridge too far? I’m accustomed to simply shooting astrophotography just using my hand controller for the GOTO’s and I have no tracking problems with 2-3 minutes subs without PremPro.
ARTCAM PRO MACH 3 WINDOWS 10
I’m running the ASIAIR Pro App on a Windows 10 machine ( larger screen) - rather than an iPad - using Blue Stacks emulation.a pretty nifty set up.
ARTCAM PRO MACH 3 SERIAL
But I loaded the FIDI driver and at 9600 baud, the RS232 serial port does connect, but drops out often. I can see the GTO WiFi network ,but no handshake with the ASI. So far I have had tried Ethernet and USB and Wi-Fi to talk to the ASI Air Pro, nothing. The ASI Air Pro mount interfaces is pretty basic, which is fine as she moves up from shooting the Milky Way with a DSLR into using the ASI CMOS cameras.
![artcam pro mach 3 artcam pro mach 3](https://i.ytimg.com/vi/f1OJsc_UE7A/maxresdefault.jpg)
We shoot astrophotography two weeks a year on the Modoc Plateau, 50 miles east of Mt. This is my first post, though I’ve been a long time Mach 1 (CP3) owner and I just bought a second used Mach 1 (CP4) for my wife.